|
|
Polaris Ranger XP HD Razor RZR RZRS Crew, Yamaha Rhino, Kawasaki Mule Teryx, Arctic Cat Prowler, Honda Big Red
|
|
|
|
|
|
|
|
The LED Turn Signal Kit will fit all years for the Polaris Ranger 425 / TM / 500 / 700 / 800 / XP / HD / Crew and Razor / RZR / RZR S, all years for the Yamaha Rhino, all years for the Kawasaki Teryx & Mule, and all years for the Arctic Cat Prowler. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
Note: some like amber lights front and rear and the Utah residence may want all amber lights, do to SB181S01 “Off-highway Vehicles Use on Public Highways” states: “Amber electric turn signals, one on each side, both front and rear”. Read the entire Utah bill here: Street Legal OHV. Order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights.
|
|
Note: the 2009-2010 Polaris Ranger XP / HD and the 2010 Ranger 800 Crew use our custom turn signal switch (TSS) mounting strap. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-10 Ranger XP/HD (TSS) Strap or 2010 Ranger 800 Crew (TSS) Strap.
Note: the 2008-2010 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.
Note: the 2010 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
This is a 12 volt LED Turn Signal Kit with 2 Amber (front) and 2 Red (rear) LED lights. The 4 LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" ground wire (for better grounding of the turn signal switch) and the hardware to mount it to your steering column.
The four LED Lights are 4”x 2” rectangular with 16 (LED) Light Emitting Diodes each, polycarbonate lens & housing and hard wired with encapsulated electronics to eliminate corrosion.
The special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER. This special electronic LED flasher is also quite, no annoying clicking sounds.
The kit includes: 2 Amber and 2 Red LED lights, the Turn Signal Switch with an extra 18” ground wire with ring tong connector (for better grounding of the turn signal switch) and the hardware to mount it to your steering column, the special LED Electronic Flasher, an in-line fuse holder, a 3 amp fuse, the self tapping screws for mounting the lights and flasher, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.
This kit can be easily installed, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
This kit was originally developed for my 2006 Polaris Ranger XP and my customers have installed their kits on the Polaris Ranger 425 / TM / 500 / 700 / 800 / XP / HD, Razor (RZR / RZR S) and Crew, the Yamaha Rhino, the Kawasaki Mule and Teryx, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
|
|
|
Total Power Draw: .32 amps, that's less than a third of an amp with all four LED hazard lights ON!
|
|
|
|
|
|
|
2 – Amber 4" x 2" LED Lights
2 – Red 4" x 2" LED Lights
1 – Turn Signal Switch w/hardware
1 – 18" Black Ground Wire (switch)
|
|
1 – LED Electronic Flasher
1 – In-line ATC Fuse Holder
1 – ATC Type 3 Amp Fuse
Complete Support by EZTSK
|
|
9 - Self Taping Screws for mounting
... LED Lights & Electronic Flasher
Mounting Installation Instructions
Wiring Instructions & Diagram
|
|
|
Options: We have some Custom Kit Brackets along with a Wire & Connector Kit that you may want to use with your Turn Signal Kit. Any of these options purchased with your kit, will save you money!
|
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
 
|
|
|
|
Not what your looking for, checkout these kits:
|
|
|
|
|
For more information:
EZ Turn Signal Kits
P. O. Box 1818
Glendale, AZ 85311-1818 US
E-mail: Cisco@LEDTSK.com
Phone: (623) 435-1337
|
|
|
|
|
|
|
|
|
