Polaris Ranger XP HD Crew Diesel 6x6 EV 400 500 700 800 RZR RZRS RZR4 RZR 900 XP, Yamaha Rhino
Can-Am Commander, Honda Big Red MUV, Kawasaki Mule Teryx, Arctic Cat Prowler, Golf Cart
|
|
|
|
|
|
|
|
|
|
|
|
Hello, my name is Cisco Folk and I am the President of EZ Turn Signal Kits & Accessories here in Glendale, AZ. My passion is the outdoors, so I purchased a 2006 Polaris Ranger XP to help me get around.
After using the old hang your arm out the side to signal on coming traffic and almost being run over twice, I decided I had enough. I wanted to install LED turn signals for my added safety. When I tried to purchase a four light aftermarket LED turn signal kit, I was unable to find anyone who had developed an aftermarket LED Turn Signal Kit. As we all know the UTV's have small batteries and small charging systems. The main reasons why I wanted all 4 turn signal lights to be LED are:
- Less current draw, resulting in increased battery & alternator life while allowing more power for other vehicle requirements.
- Faster illumination offers significant safety benefits for following drivers to react quicker, resulting in an average of a three foot reaction time advantage for every 10 miles per hour.
- LEDs have no filament, therefore are not susceptible to shock & vibration, a major cause of failure for lamps with incandescent bulbs.
|
|
|
So, I created my own aftermarket LED Turn Signal Kit. I wanted DOT approved, good looking, clean and crisp LED lights, ones that were very visible, even during the day. The LED Lights in my turn signal kits are not only bright, but they are hard wired with encapsulated electronics to eliminate corrosion. They have both the positive (+) and negative (-) wires to make a great connection, no screw through a metal surface to the frame for ground. You can hard wire the lights to both positive and negative, so you always have a good connection.
|
|
|
|
|
The Turn Signal Switch is heavy duty, has the right and left turn signals along with a pull out flare tab for the 4-way emergency (hazard warning) flashers.
|
|
|
I designed and developed a custom turn signal switch (TSS) mounting strap for the 2009-2010 Polaris Ranger 500, the 2009-2012 Polaris Ranger XP & HD, the 2010-2012 Polaris Ranger 800 Crew & 6x6, and the 2011-2012 Polaris Ranger Diesel models. This professional looking mount will allow full range of motion and clearance for the tilt steering wheel.
|
|
|
I designed and developed a custom turn signal switch (TSS) mounting plate for the 2010-2012 Polaris Ranger EV & 400 and the 2011-2012 Polaris Ranger 500 & 500 Crew models. This professional looking black powder coated plate looks and works great on the Ranger's.
|
|
|
I designed and developed a custom turn signal switch (TSS) mounting bracket for the 2011-2012 Can-Am Commander. This professional looking black powder coated bracket is very EZ to install and it looks great on the Can-Am Commander's.
|
|
|
I designed and developed a custom turn signal switch (TSS) mounting bracket for the 2009-2012 Honda Big Red MUV. This professional looking black powder coated bracket looks and works great on the Honda MUV's.
|
|
|
I have seen several turn signal switches out there that come with a hose clamp, not this company. You will always get good looking, high quality aftermarket turn signals from EZ Turn Signal Kits!
|
|
|
I was the first to develop and market the LED Turn Signal Kits for the UTV side-by-sides! Our kits can be easily installed on any side-by-side, UTV, Golf Cart, Sand Car, Dune Buggy, etc.
|
|
Check out our entire stock of aftermarket turn signal kits & accessories and if you have any questions, please contact us, we are here to help you!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For more information:
EZ Turn Signal Kits
P. O. Box 1818
Glendale, AZ 85311-1818 US
E-mail: Cisco@LEDTSK.com
Glendale Office #1: (623) 435-1337
Glendale Office #2: (623) 939-0834
|
|
|
|
|
